Search found 152 matches

by TWIMCAM BOY
Fri Aug 20, 2010 3:02 pm
Forum: Twin Cam Land
Topic: Oil Pressure
Replies: 34
Views: 6213

how did you go with the engine??? it did have high oil presure from day dot i think from memory the builder did adjust the relieve valve but thats going back along time ago now. when i sold it too you it hadn t even done more then 150kms which was all on the dyno it hasnt had a hard life at all how ...
by TWIMCAM BOY
Mon Apr 06, 2009 6:21 am
Forum: Buy / Sell
Topic: JA TWINCAM ENGINE
Replies: 14
Views: 3143

car is sold guys the new owner is sargret khan
hope you enjoy the car
by TWIMCAM BOY
Wed Mar 18, 2009 3:38 pm
Forum: Buy / Sell
Topic: JA TWINCAM ENGINE
Replies: 14
Views: 3143

hey guys it still for sale just sitting in garage looking good :D
if you s want any more info please call me on 0408992232 russell
by TWIMCAM BOY
Fri Nov 28, 2008 8:07 am
Forum: Buy / Sell
Topic: JA TWINCAM ENGINE
Replies: 14
Views: 3143

since i have finished this engine it only been on the dyno for a run in tune it only made something worthless like 230rwhp but i did n t even get a print out i could ring up and get one if its really needed. im only selling as i have too many toys but if no one buys it ill just kept it. have have re...
by TWIMCAM BOY
Thu Nov 27, 2008 8:21 am
Forum: Buy / Sell
Topic: JA TWINCAM ENGINE
Replies: 14
Views: 3143

pics up engine bay photo is about 3 mths ago ill get a new one this weekene
by TWIMCAM BOY
Wed Nov 19, 2008 1:56 pm
Forum: Buy / Sell
Topic: JA TWINCAM ENGINE
Replies: 14
Views: 3143

ill try and put some up tonight or thrusday
by TWIMCAM BOY
Mon Nov 17, 2008 12:03 pm
Forum: Buy / Sell
Topic: JA TWINCAM ENGINE
Replies: 14
Views: 3143

JA TWINCAM ENGINE

Hi guys the time has come to sell my toy :cry: 1983 JA STARION 1994 vr4 ENGINE:- eagle rods aries pistons nitred crank acl race bearings o'ring head ralliart head gasket titanium retainers crower valve springs stainless valves adjustable cam gears gates timing belt gt35/40 .63 38mm external gate cus...
by TWIMCAM BOY
Sun Nov 25, 2007 5:35 pm
Forum: Show And Go
Topic: my ride (have a Look) im a new member
Replies: 33
Views: 4947

awesome colour mate and i love the body kit. great to see another twim cam out there!!!!!!!!!!!! :D where about s do you live???? any work too the engine???
by TWIMCAM BOY
Wed Jun 27, 2007 7:50 pm
Forum: Technical
Topic: fitting rwd water pump to vr4 motor
Replies: 3
Views: 902

hey mate not sure on the pulley your refering too but as for the bottom crank pulley i juat ran a vr4,evo or rvr one but as for the water pump i couldn t tell you the exact one i went to a mitsy wreackers and picked one off the shelf.
by TWIMCAM BOY
Wed Jun 27, 2007 7:36 pm
Forum: Technical
Topic: Microtech with twin cam conversion?
Replies: 8
Views: 1702

well i went over the wiring again today and can t find the problem its as if the regulator at the front stays engaged even when i pull the fuse out under the dash(fuse panel) the front regulator starts clinking non stop! any ideas people?
by TWIMCAM BOY
Tue Jun 26, 2007 6:12 pm
Forum: Technical
Topic: Microtech with twin cam conversion?
Replies: 8
Views: 1702

funny you mention the wipers cause mine do the same but i think i have just fu#k up the wiring by earthing it out somewhere. i still havent found the problem wooops rofl
by TWIMCAM BOY
Tue Jun 26, 2007 6:08 pm
Forum: Technical
Topic: Cheaper Substiture Than LSD?
Replies: 31
Views: 5065

hey guys, i have been in a few cars with lockers solid rear that arnt to bad to drive even in the wet.but my starion (irs of cause) is by far the worst its horrible to drive it bucks really bad at low speed obvisously the slower the worst. Its comin out of the car it s that bad i would be surpised i...
by TWIMCAM BOY
Tue Jun 26, 2007 5:54 pm
Forum: Technical
Topic: fitting rwd water pump to vr4 motor
Replies: 3
Views: 902

hey i did my water pump on my last engine about two years ago so im not 100% sure on how much i took off it to clear the timing belt. When i fitted it i just kept refiting the timing belt and marking where it hit then pulling it off and grinding it down it took about 4 times before it cleared i took...
by TWIMCAM BOY
Sun Jun 24, 2007 6:45 pm
Forum: Technical
Topic: Microtech with twin cam conversion?
Replies: 8
Views: 1702

hey mate,
im currently running a mircotech ltx8 on my twin cam. it works perfect no complaints at all.
by TWIMCAM BOY
Tue May 08, 2007 4:16 pm
Forum: Buy / Sell
Topic: wtb LSD
Replies: 7
Views: 1561

hey thank s for the reply s guys. Well prices im not really sure about i can get one from oscar for $740 to my door so around $600 mark what does everyone think is a fair price??? thanks