Austarion

Neil wrote:Would the pistons and rods be OK in a Starion Block?

Pretty sure the only difference is the gudgeon pin, so it SHOULDN'T be a problem as long as you get both.


Cheers.

If you are going with the original starter position for the VR4 engine, you will probably need a VR4 flywheel because they are physically smaller than the Starion flywheel, even though the Starion flywheel will bolt straight on. If the bellhousing fabricator is good, he should be able to reposition ...

FG Falcon spec Tremec TR-6060 (T-56) Is the adapter from Bill Hincher? Actually should be around $5 for the bearing. The bearings I buy are supposed to be "special" in they are a little loose when cold(not the shell, the actual balls). When they heat up they are on size. This type of bear...

I'm not using a starion block though! Mine is all VR4 What gearbox are you planing on using as this will decide what flywheel/clutch will fit? Stock clutch is 9", still all fits being 10" clutch? Also, does the flywheel come with a centre bearing? Doug believes the clutch will fit so I wi...

This would be the setup that I have been talking to Doug about via email He showed me your email and aske if it would fit. I informed him that if you were using a Starion block, it will work. Could have gone lighter but decided 9mm was the thinnest we should go on the thrust surface. They have gone...

EBOULAR, contact NPC for shipping costs as all I've done is to talk my brother into making a retail batch of them.


These flywheels will fit either the standard 2.0L Starion 4G63t and the imported Starions with the 2.6L Astron 4G54 (wideblock) engines.

Hope this helps.


Cheers.

Finally had my brother make a batch of lightened billet steel flywheels and currently there are 6 left. The flywheel weighs in at 6.15kg http://110.174.47.143/SG/NPC/NPC-FLYWHEEL.jpg Still waiting on the final cost but it will be under $400 There are 3 options for the pressure/friction plate. STREET...

4g63 Twincam VR4 head, big inlet ports. 1. Fully reconditioned, never installed. 2. NEW 1mm oversize Stainless valves. 3. NEW Bronze valve guides. 4. NEW Gen-3 Hydraulic lifters. 5. VRS Gasket kit. $750+shipping. 4g63 Twincam RVR head, small inlet ports. 1. CAS is on the FRONT of the head so no &quo...

Hi superscan, I would be interested in the plastic top, middle and bottom timing belt covers, but I need them posted to the uk. Is this possible? If so what's the costs involved? Cheers, T-man. I will be removing and keeping the engines and gearboxes from all these cars just before I scrap them. So...

Last Chance.

Vehicles being scrapped at the end of the week.


Cheers.

Items: 3 Twincam 4g63 GSR Galants '89, '90, '91 Location: Sydney Item Condition: See below Pictures: See below Price: $1500 JOB LOT ... NOT NEGOTIABLE ... Postage: not likely Contact Details: PM or post here. WHITE '91 HG GSR http://110.174.47.143/SG/FOR-SALE/HG-HH_Galants/FS-005.jpg http://110.174....

Thanks for the replies. I'll let him know.

Cheers.

Were the 2.6L M8 style Astron heads ever used in NZ? There is a person off an American Starion site that is wanting a M8 head with the kidney shaped chamber. They were on the TS Magna's (around 1992 to 1996 I think). http://110.174.47.143/SG/Head/M8/M8-chamber.jpg Shipping from Australia to US is be...

Will be heading up to Ballina and back, early in the new year, with an almost empty Triton ute. After I return, I'll be heading over to Adelaide with an empty car trailer and ute but both will be fairly full on the return trip. If anyone needs some some stuff (tyres/gearbox/engine/diff/car etc..) sh...

thrash wrote:also, what price are we looking at? I think people tend to assume that if price is not mentioned, it's already going to be too expensive..

Price looks to be approx $430 but may be a bit lower if there is a decent number of people buying one.


Cheers.